Search found 19 matches

by turtle
Wed Sep 25, 2019 7:37 pm
Forum: QCAD 'How Do I' Questions
Topic: drawing has open contour - how to detect, where?
Replies: 5
Views: 274

Re: drawing has open contour - how to detect, where?

Super helpful post this got me out of a jam today when I was attempting another fill.
I was getting a "loop not closed at point xx yy" error.
by turtle
Wed Sep 18, 2019 11:08 pm
Forum: QCAD Troubleshooting and Problems
Topic: How can I close this loop?
Replies: 4
Views: 454

Re: How can I close this loop?

Thank you so much got it now!!
:P
Given the dimensions 1/2" = 1FT what would be the best scale?
The steel pattern seems to be either too big or too small around .16

WOOPS EDIT thats 1/8" = 1FT
by turtle
Wed Sep 18, 2019 10:47 pm
Forum: QCAD Troubleshooting and Problems
Topic: How can I close this loop?
Replies: 4
Views: 454

Re: How can I close this loop?

Thanks Husky, I forgot to check for those Zero length entities, however duplicates are not being found: (Perhaps I deleted them already in all my futzing around.) Command: reset Command: zerolength Zero-length entities found: 1 Zero-length entities found: 1 Zero-length entities found: 1 Zero-length ...
by turtle
Wed Sep 18, 2019 12:46 am
Forum: QCAD Troubleshooting and Problems
Topic: How can I close this loop?
Replies: 4
Views: 454

How can I close this loop?

When using the hatch tool to make a new hatch or hatch by segments how do I solve a loop not closed error ?
Is there some kinda of macro I can write to merge all points in a selection that are less than 1000th of an inch or some distance from each-other?
Thanks in advance!
by turtle
Fri Jun 21, 2019 12:29 am
Forum: QCAD 'How Do I' Questions
Topic: How do I align the size by layer?
Replies: 1
Views: 1278

How do I align the size by layer?

Greetings all Qcadders again I am continuing to learn more and work my way thru chapter 13 in this Qcad book (the chapter on text). However I have a continuing problem that the scale of text gets way off only inside the "edit" box. While it looks fine on the drawing. I typically draw work in actual ...
by turtle
Tue Apr 16, 2019 6:46 pm
Forum: QCAD 'How Do I' Questions
Topic: Need a little help setting up a template.
Replies: 2
Views: 399

Re: Need a little help setting up a template.

Hi, no need to play around with Linear factor ect. Just break the math down: you will print with a 1/4" = 1' scale on a ANSI B, that scales everything down in your drawing to fit on an ANSI B. To be exact it scales it 48 times smaller, to counter that you have to enlarge entities like frame / title...
by turtle
Fri Apr 12, 2019 2:55 am
Forum: QCAD 'How Do I' Questions
Topic: Need a little help setting up a template.
Replies: 2
Views: 399

Need a little help setting up a template.

Greetings all, I am working on making some templates for what I usually work in 11X17" A3 paper and US units.
I am having a hard time setting up reasonable scales of text and the default 'Linear Factor' seems to be tied to the printing scale of 1/4 IN = 1 Foot.
Any tips?
Template attached.
Thank you.
by turtle
Tue Apr 09, 2019 6:28 pm
Forum: QCAD Troubleshooting and Problems
Topic: hatch pattern too dense. hatch pattern generation aborted
Replies: 4
Views: 532

Re: hatch pattern too dense. hatch pattern generation aborted

Thank you, I find it really helps to have the printed copy of your book, but I am still going to have lots of questions on here. :mrgreen: I see now my 7 attempts were successful just at the wrong scale ;) I never thought it would let me put a hatch on a hatch. I take it the best way to clean it up ...
by turtle
Mon Apr 08, 2019 4:03 pm
Forum: QCAD Troubleshooting and Problems
Topic: hatch pattern too dense. hatch pattern generation aborted
Replies: 4
Views: 532

Re: hatch pattern too dense. hatch pattern generation aborted

Thanks for the quick reply!
Is there a way I can change the hatch in that drawing at that scale so it does not slow down Qcad?
by turtle
Mon Apr 08, 2019 3:33 am
Forum: QCAD Troubleshooting and Problems
Topic: hatch pattern too dense. hatch pattern generation aborted
Replies: 4
Views: 532

hatch pattern too dense. hatch pattern generation aborted

I tried to make a hatch in my drawing and now qcad is slowing down to a crawl and I am getting the following on my console: Warning: RHatchData::getPainterPaths: hatch pattern too dense. hatch pattern generation aborted (timeout set to 2000 )... Warning: RHatchData::getPainterPaths: hatch pattern t...
by turtle
Sun Apr 07, 2019 9:16 pm
Forum: QCAD 'How Do I' Questions
Topic: [solved] How do I paste aligning other than middle or grid?
Replies: 1
Views: 246

Re: How do I paste aligning other than middle or grid?

Ahh to answer my own question 'copy with reference' does it.
by turtle
Sun Apr 07, 2019 8:41 pm
Forum: QCAD 'How Do I' Questions
Topic: [solved] How do I paste aligning other than middle or grid?
Replies: 1
Views: 246

[solved] How do I paste aligning other than middle or grid?

Greetings I would like to copy a wall and paste it aligning its right side to an existing line. I have tried the options in the 'snap' menu, all of them still give me the yellow 'middle' or 'grid' options. The restrict horizontal and vertical seem to pick arbitrary locations. I am hoping to paste wi...
by turtle
Fri Apr 05, 2019 5:15 pm
Forum: QCAD 'How Do I' Questions
Topic: How do I close a loop?
Replies: 7
Views: 853

Re: How do I close a loop?

Ahh thank you!!
I am slowly learning this every day!
by turtle
Fri Apr 05, 2019 4:57 pm
Forum: QCAD 'How Do I' Questions
Topic: How do I close a loop?
Replies: 7
Views: 853

How do I close a loop?

Greetings I have a circle with some lines crossing. I would like to fill in the area between the line on the right and the edge of the circle. I am getting the error 'Loop not closed at point' ... Not sure how to locate the point that is not closed. I tried explode and making a block out of the sele...
by turtle
Thu Dec 13, 2018 10:14 pm
Forum: QCAD 'How Do I' Questions
Topic: Browse Tool?
Replies: 3
Views: 728

Re: Browse Tool?

Thanks All!

Go to advanced search